Como retirar a argamassa antiga das juntas sem lascar os cantos dos tijolos

O planejamento rigoroso e a estimativa correta de materiais são cruciais para a durabilidade e integridade estrutural de qualquer projeto de rejuntamento. Este guia técnico detalha as formulações geométricas, normas aplicáveis e práticas de canteiro para Como retirar a argamassa antiga das juntas sem lascar os cantos dos tijolos.

1. Geometria volumétrica da junta e fórmulas fundamentais

V_cavity = L_joint * w_joint * d_rake
V_total  = V_cavity * (1 + Waste% / 100)

A common source of contractor miscalculation is confusing surface wall area with internal joint void volume. Because mortar joints occupy only a percentage of the total wall face, calculating mortar requirements requires resolving:

1. Total visible joint run ($L_{joint}$): The sum of all continuous horizontal bed joints and vertical perpendicular (perp) head joints across the surveyed elevation.
2. Visible joint face width ($w_{joint}$): The nominal face dimension between adjacent masonry units (typically 10 mm in modern work).
3. Raked fill depth ($d_{rake}$): The clean cavity depth from the brick face to the sound bedding mortar (which must never be less than 2× the joint width, or a minimum of 15–20 mm).

When repointing regular brickwork in stretcher bond, the repeating rectangular module ($L_u + w_j$) by ($H_u + w_j$) yields the exact linear metres of joint per square metre without double-counting intersections:

$$k_j = \frac{L_u + H_u + w_j}{(L_u + w_j)(H_u + w_j)}$$

2. Conformidade com normas europeias e britânicas (BS EN)

All mortar calculations must reference established technical standards:

• BS EN 771-1: Specification for clay masonry units (standard metric work size: 215 × 65 mm).
• BS EN 771-3: Specification for aggregate concrete masonry units (dense and lightweight blocks: 440 × 215 mm).
• BS EN 998-2: Specification for factory-made masonry mortar (wet yield, bulk dry densities, and flexural bond strength).
• BS EN 459-1: Building lime definitions, specifying Natural Hydraulic Lime (NHL 2, NHL 3.5, NHL 5) and non-hydraulic putty.

Under these standards, dry pre-blended lime and cement mortars produce predictable wet yields between 14.0 and 15.6 litres per 25 kg bag, corresponding to compacted bulk densities between 1,600 and 1,785 kg/m³.

3. Execução em obra, profundidade de remoção e acabamento

Before placing new mortar, joints must be prepared with sound tradesmanship:

• Raking depth: Rake back old decayed mortar to at least twice the joint width (15–20 mm for standard 10 mm brick joints). Shallow feather-edged pointing will pop out during the first winter freeze cycle.
• Arris protection: Use hand plugging chisels or oscillating carbide boots rather than high-speed angle grinders. Grinder runouts cut deeply into brick edges, causing permanent aesthetic and structural damage.
• Dust extraction & dampening: Flush joints with clean water mist before pointing to prevent dry suction from robbing the fresh mortar of hydration water.

4. Orçamento de materiais e lista de compras para canteiro

When converting calculated net cavity volumes into material purchasing orders:

• Standard brickwork default waste: Apply 10% waste for droppings, raking depth variance, and compaction.
• Rough stone or rubble masonry: Apply 15% to 20% waste allowance due to undulating depth cavities.
• Pack counts: Divide total waste-adjusted volume by manufacturer declared yield per bag (e.g., 14.5 litres per 25 kg bag for NHL 3.5) and always round up to the next whole bag.

Always use our online Pointing Calculator to obtain exact cavity volumes, weight conversions, and material bags for your specific project dimensions.